The short answer: Finish a full winterizing routine in one afternoon by cleaning, drying for 30–60 minutes, protecting exposed metal and wood, and storing soft goods in sealed bins; total active work is typically 2–4 hours.
Prep and Clean
Start on a dry day with temperatures above 40°F (4°C). Move furniture into an open 10 ft by 10 ft work area so cushions and covers can lie flat and frames are accessible from all sides. Remove cushions, seat pads, and throw pillows first and set them on a clean tarp or table to keep them off the ground.
Label removable pieces during disassembly: use numbered masking tape on each part and a zip bag for the matching screws so reassembly takes 10–20 minutes later. If a piece requires tools, plan 10–15 minutes to strip and lay out bolts—an adjustable wrench or 7/16 and 1/2 inch sockets cover most fasteners on common sets.
Make cleaning solutions in a 1-gallon bucket. For general dirt: mix 1 gallon (3.8 L) warm water with 2 tablespoons of liquid dish soap. For mildew-prone spots: mix 1 gallon water with 1 cup white vinegar. For sensitive wicker and painted surfaces use a soft nylon brush; for metal and glass use microfiber cloths. Always spot-test a cleaner on an inconspicuous 2 in x 2 in area for 5 minutes before full application.
For greasy grime on metal frames make a paste from 2 parts baking soda to 1 part water; apply with an old toothbrush, scrub 30–90 seconds per spot, then rinse. For teak or unfinished hardwood, avoid saturating the wood: clean with 1/2 cup mild soap per gallon of water, wipe with a damp rag, then immediately dry with a clean towel to remove surface moisture.
Rinse frames with a garden hose set to low pressure (below 1,000 psi). For glass tabletops use 1 part vinegar to 3 parts water and a squeegee; allow glass to air-dry 10–15 minutes to avoid streaks. After rinsing, towel-dry fasteners, joints, and crevices to remove trapped water—use a shop vacuum with a soft brush attachment for deep cushion seams and zipper channels.
Machine-wash removable cushion covers if the manufacturer label allows: use a warm wash at 40°C (104°F) on a gentle cycle and tumble-dry on low for 20–30 minutes or air-dry flat for 1–3 hours. If covers are not machine washable, spot-clean with the vinegar solution and let them dry flat in sun for 1–3 hours until the surface is dry to the touch.
Tools and materials
Mixes, settings, and times for one dry afternoon.
Spot-test 5 minutes
Try every mix on a hidden 2 by 2 in patch for 5 minutes before washing the whole frame.
Dry 1 to 3 hours
Air cushion covers flat 1 to 3 hours and glass 10 to 15 minutes so nothing stores damp.
“A routine that prioritizes drying and sealing vulnerable joints cuts winter damage dramatically; spend 15–30 minutes on fasteners and covers to protect months of use.”
—

Protect and Store
Inspect hardware and fasteners closely. Tighten loose screws and replace any visibly rusted bolts; remove surface rust with 120-grit sandpaper for 1–2 minutes per spot, wipe clean with a damp cloth, and apply a thin coat of rust-inhibiting primer or paste wax to exposed metal. For stainless fasteners spray a light coat of silicone lubricant and cycle the hinge or joint 3–5 times to distribute the lubricant evenly.
When disassembling larger sets, keep an inventory: place parts for each chair or table into separate zip-top bags and number them to match the masking-tape labels. Expect disassembly for a 4-piece set to take 20–30 minutes and reassembly to take a similar amount of time in spring.
Treat wooden furniture according to finish type. For unfinished hardwood sand any rough spots with 120–150 grit paper, remove dust, and apply one coat of outdoor oil or sealer following the product directions; allow 24 hours cure before exposure. For painted or pressure-treated wood touch up worn spots with outdoor-grade paint or stain, applying 2 coats if needed and allowing 2–4 hours drying between coats.
Cushion care: vacuum each cushion for 2–3 minutes, spot-clean stains using a 1:4 vinegar-to-water solution and a soft brush, then air-dry flat for 1–3 hours or until surface is dry. Pack cushions in 27–40 gallon plastic bins with 1–2 silica gel packs (6–10 g each) per bin to reduce moisture; label bins with a permanent marker and store off the floor on a pallet or shelf at least 6 inches above the ground to prevent cold dampness.
Select covers that match your set’s footprint: a three-seat sofa typically needs a cover about 84″ x 40″. Secure covers with bungee cords or straps using a 3:1 loop spacing—one strap every 3 feet of cover edge—to keep covers snug in wind. In exposed locations choose ventilated covers with 2–3 built-in vents to prevent condensation; never wrap furniture airtight where trapped moisture will accelerate finish failure.
Storage layout: if storing frames indoors, nest lightweight chairs inside one another and stand heavier tables on their side to save space; leave at least 2 inches between items for airflow. In an unheated garage maintain a stable temperature above 35°F (2°C) to reduce freeze-thaw cycles that crack sealants and finishes. If you must store items outside, elevate them on pallets and avoid touching soil or grass directly.
Final checklist should take 5–10 minutes: tighten fasteners, wipe down glass, place cushions in bins, apply covers, and secure straps. Expect 30–60 minutes of passive drying after cleaning plus 60–90 minutes of active protective steps; with two people you can typically finish a medium set in under 2 hours, one person in about 3–4 hours.

Frequently Asked Questions
Further reading: How to Lay a Simple Gravel Patio in a Weekend · Mulching: Suppressing Weeds Naturally
Sources: National Park Service
